Save These Instructions
- Please plug the charger into an AC wall socket/outlet with a rated voltage of 100~240V
- The product is designed for use with IT equipment only. Do not use the charger with any product which is not in conformity with rated specifications of this charger.
- It's normal for this charger to heat up a little during use.
- In case the charger stops charging suddenly, this may be due to an incident of over-current/over-temperature/over-voltage/short-circuit protection. In this case, please unplug the connected device/s. Reconnect your device/s after 30 seconds, the charger will resume normal functioning.
- Do not place the charger close to any sources of heat such as fire, stove, candles etc.
- Please ensure that no form of liquid is split on the charger. (Any such spill of any liquid on the charger voids the warranty on the product).
- The maximum ambient temperature during use of the appliance must not exceed 25°C.
- The disconnection from line voltage is made by AC plug.
- Only use a dry cloth or brush to clean the charger.
- In case of failure or component defect, don't attempt to repair the charger. Please reach out to Wozoyo customer support.
| Item | Specification |
|---|---|
| Total Wattage | 140W Max |
| Input | 100-240V ~, 50/60Hz 2A Max |
| Output | USB-C1: 5V⎓3A, 9V⎓3A, 12V⎓3A, 15V⎓3A, 20V⎓5A, 28V⎓5A (140W Max) USB-C2: 5V⎓3A, 9V⎓3A, 12V⎓3A, 15V⎓3A, 20V⎓5A, 28V⎓5A (140W Max) USB-A: 5V⎓3A, 9V⎓2A, 12V⎓1.5A (18W Max) USB-C1+USB-C2: 100W+35W USB-C1+USB-A: 100W+18W USB-C2+USB-A: 100W+18W USB-C1+USB-C2+USB-A: 65W+45W+18W |
- Single Tap the control button located on the top of the charger to toggle between different UI options.
- Long Press the control button located on the top of the charger to rotate the display screen orientation.
| UI | Graphic | Description |
|---|---|---|
| Home Screen |
|
When powered on, the Wozoyo logo is displayed on the screen of the device. |
| Standby Mode |
|
If charger is not in use, after 5 seconds, the device enters standby mode and displays emojis. Note: Tap the control button or plug in a charging cable to exit standby mode. |
| Power Distribution |
|
In this user interface, power drawn by each port can be observed. |
| Smart Temperature Monitor |
|
In this user interface you can track the live temperature status of the charger. "We Chilling" means the charger's temperature is on the lower side. "Getting Toasty" means that charger is running in high performance mode and temperature has risen slightly but still lies well below international operating temperature limit. "Cool it baby" means that charger's temperature has risen and cooling measures have been activated but temperature still lies below international operating temperature limit. |
| Total Operating Time |
|
In this user interface you can track the total operating time of the charger. Activates after the charger has been in use for 1 hour or more. |
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Please note that changes or modifications of this product is not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Company Name: Secure Connection Limited
Address: 807, Arion Commercial Centre, 2 - 12 Queen’s Road West, Sheung Wan, Hong Kong
Telephone: +852 5803 1828
Download English Manual